1-Gang Box Cover, Material: Steel, Finish: Zinc Electroplate, Number Of Outlet: (1) Square Handle Tumbler/Toggle Switch, Mounting: Box, For Use With Square Handle Tumbler or Toggle Switches

Works On All Siding Types. Before or After Siding Is Up, Mounting Holes On Inside Of Box. Textured Paintable Surface. NM Cable Connector Provided. 6-1/2 X 6-1/2 Mounting Surface. Provides A .895 J-Channel. 24.5 Cubic Inch Box. With Flange.

Steel 4X4 Box For Concrete Block Walls. 1/2" and 3/4" Knockouts. Spring Steel Clip Holds Box Securely Against Walls When Screws Are Tightened. Screw Hole Pattern For 4X4 and Two Gang Devices. 42.3 Cu. In.

Cantex EZ55TO Ez Box Is A 3-Gang 55 Cu. In. Renovation (Old Work) Electrical Switch or Outlet Box Is For Residential or Light Commercial Renovation (Old Work) Projects When A 3-Gang Box Is Needed. Ez Mount Flanges, Winged Swing Tabs and Built In Wire Clamps Make Installation Easy and Cost Effective.

1-Gang Blank Box Cover, Material: Copperfree (4/10 Of 1 PCT Maximum) Aluminum, Finish: Epoxy Powder Coat, Mounting: Box, For Use With Unilets FS and FD Single Gang and Tandem Cast Hub Device Boxes

1-Gang Blank Box Cover, Material: Copperfree (4/10 Of 1 PCT Maximum) Aluminum, Finish: Epoxy Powder Coat, Mounting: Box, For Use With Unilets FS and FD Single Gang and Tandem Cast Hub Device Boxes

Eaton B-Line Series Acoustical Tee and T-Bar Fasteners, Acoustical Tee, 1" Height, 1" Length, 1" Width, 0.41LBS, Box Hange 30" Span, Electrical Box T-Bar Fasteners, 20 LBS Load Capacity

The EZ18SO-HW Is The Cantex 1-Gang Heavy Wall Electrical Switch and Outlet Ez Box For Renovation Projects (Old Work). This Heavy Duty Box With Winged Mounting Tabs Is Perfect For Residential and Light Commercial Applications Where An Electrical Switch or Outlet Box May Be Exposed to The Elements.

Cantex EZ68QO Ez Box Is A 4-Gang 68 Cu. In. Renovation (Old Work) Electrical Switch or Outlet Box Is For Residential or Light Commercial Renovation (Old Work) Projects When A 4-Gang Box Is Needed. Ez Mount Flanges, Winged Swing Tabs and Built In Wire V-Clamps Make Installation Easy and Cost Effective.

EZ34DO-HW Is The Cantex 2-Gang Heavy Wall Electrical Switch and Outlet Ez Box For Renovation Projects (Old Work). This Heavy Duty Box With Winged Mounting Tabs Is Perfect For Residential and Light Commercial Applications Where An Electrical Switch or Outlet Box May Be Exposed to The Elements.

One Box® Non-Metallic Outlet Boxes. Four Gang. Vertical. Fast and Easy to Install.

Floor Box, Polycarbonate (Box);Brass (Cover);Closed Cell Rubber (Gasket);Nitrile (O-Ring);Plated Carbon Steel (Fastener);Galvanized Steel (Dust Plate);Nonmetallic (Pop-In Cable Clamp) Material, Black, FB Model, 24.5 Cu.In Capacity, (2) Molded In Speed Clamp Cable Entry, 1 Gang, Rectangular, Side:(2) 1/2 In;Bottom:(1) 1/2 In Knockout Size, 4 Knockouts, Floor Mount, 2.5 In Length, 3.5 In Width, 4.31 In Height, 15 LB

Floor Box Kit With Steel Box and Metallic Cover With Threaded Plugs. Single Gang. Nickel.

Floor Box Kit With Steel Box and Metallic Cover With Threaded Plugs. Single Gang. Brass.

Receptacle With Box Cover, Number Of Poles: 2, Number Of Wires: 3, Amperage Rating: 15 Amp, Voltage Rating: 125 V, Material: Malleable Iron, Nema Rating: Nema 5-15R, Mounting: Box, For Use With Single Gang Device Boxes

Cantex EZ18XN Ez Box Is An 18 Cu. In. 4 In. Square PVC Box For Residential or Light Commercial New Construction (New Work) Electrical Installations With A Molded Flange and Enhanced Angled Nails For Ez Mounting. 4 In. Square Boxes Provide Maximum Volume For Multiple Conductors and Connectors That Often Run In Two or More Directions.

<P>For Surface Mounting Of Alarm Devices and Safety Signals Designed to Fit Into 4'' (102MM) Square Back Boxes. Available In Red and Ivory Finishes. Cover Is 2 3/4'' (70MM) Deep and Has Three Twistouts For Raceways On Each Side. Base Has 1/2'' and 1'' Concentric and Single-Gang Box Kos. Accepts Nema Double-Gang Standard Faceplates.</P>